FFT Spectrum analyzer ZET 032

  • 2 input channels;
  • integrated power amplifier;
  • support of ICP (IEPE), DeltaTron, ISOTRON transducers, charge transducers, and voltage output sensors;
  • compact product version

POR (price on request)

Specifications

of FFT Spectrum analyzer ZET 032

Technical specifications
Input specifications
Number of channels 2
Input type by voltage
ICP
by charge
Input voltage range at the minimal amplification ratio ±10 mV
Programmable amplification ratios 1, 10, 100
Frequency ranges of the simultaneously analyzed signals DC…20, DC…200, DC…2 000, DC…20 000 Hz
Anti-aliasing filtration of signals up to 40 kHz
LPF filters are implemented as digital Butterworth filters 120 dB/oct for the following sampling frequencies: 50 Hz, 500 Hz, 5 kHz, 50 kHz
Digital filters with frequency adjustment in compliance with the provisions of IEC 61672-1:2002 А, В, С, D for the 1-st class precision noise meters
Input specifications in the “Charge” mode
Amplification ratio by charge 1 mV/pC; 10 mV/pC; 100mV/pC
Maximal input charge (peak value) at the amplification ratio “1”, min. 104 pC
Operating frequency range at the limits of -3dB at the non-linear distortion ratio below 10%: 0,1… 20 000 Hz
RMS noise value applied to the input in the “Charge” mode for the capacity of the transducer of 1 nanofarad in the frequency range of 0.1 Hz … 20 kHz (at the amplification ratio of 1 mV/pC), max. 0,05 pC
Output specifications
Analog outputs number 1
Output voltage range at the minimal amplification ratio ±10 mV
Frequency range of the generated signal 0,03… 20 000 Hz
Output resistance 50 Ohm
Maximal output current 20 mA
Digital input/output
Digital input 8 bit
Digital output 8 bit
Digital input/output logic type TTL
Metrological specifications
Input
Dynamic range 110 dB
Channels non-identity in the passband 0,1 %
Cross-channel phase difference 1° per 10 kHz
Intrinsic noise level applied to the input at the entire pass-band and at the maximal possible amplification ratio, max. 1 µV
Output
Admissible error limits for the frequency value in the range of 10…20 000 Hz ±0,1 %
Admissible error limits for the frequency value in the range of 0,03…10 Hz ±10 %
Admissible error limits for output DC and AC voltage ± (0,005U + 10) mV
Harmonic ratio of the generated sinusoidal signal 0,1 %
Operational specifications
Dimensions 160 × 130 × 35 mm
Weight 0,6 kg
Consumed power max 6 W
Types of supported transducers ICP (IEPE), DeltaTron, ISOTRON
Possibility of synchronization with other FFT Spectrum analyzers yes
Non-volatile memory volume (flash-drive)* up to 32 Gb
Sampling frequency of the data recording to the flash drive by a channel * 50 kHz
Duration of data recording to the flash-drive by all the channels at maximal sampling frequency* 43,2 hrs
Data rate via Ethernet 100 Mbps

Description

of ZET 032 FFT Spectrum analyzers

Multi-functional FFT Spectrum analyzers ZET-032 are intended for measurement of spectral components parameters of acoustic and vibroacoustic signals as well as for generation of electrical signals with normalized metrological characteristics.

FFT Spectrum analyzers ZET 032 can be used independently or within the framework of automated systems and technological processes control systems for scientific research purposes. Operating principle of models from ZET 032 series is based on parallel (simultaneous) analysis of signals spectra. The instruments have compact dimensions and can be used in compact laboratory environments or be used as portable measurement instruments.

When used together with ZETLAB ANALIZ software, FFT Spectrum analyzers allow to solve the following tasks:

signal analysis in real-time mode, analysis of previously recorded signals;
octave and 1/3-octave analysis based on the implementation of parallel digital filters;
narrow-band spectral analysis;
measurement of AC and DC voltage;
measurement of electrical signals frequency;
generation of sinusoidal signals and DC signals;
signals recording (digitized values of the registered signal values are saved to the integrated memory of the device).
Information of the measurement results is displayed at the external instruments in a user-friendly format.

Integrated charge amplifier allows to connect a wide range of the measurement transducers, thus it becomes possible to implement a wide range of additional functions without the need to use additional instruments.

Basic configuration

of ZET 032 FFT Spectrum analyzers

Базовая комплектация ZET 032

Basic delivery scope of ZET 032 FFT Spectrum analyzer includes the following items:

  • data acquisition controller ZET 032;
  • power supply module 220V →12V;
  • Ethernet cable;
  • BNC-BNC cable (length: 0,6 m);
  • plug 50 Ohm;
  • connector DB 9;
  • set of operational documentation;
  • case for transportation.

Order form - If you want to place an order or to make a request regarding technical specifications of particular product, fill out the form below:

Data protection notification

Please note that the personal data provided by you is used exclusively for the purposes of fulfilling our contractual obligations, including, but not limited to: issuing invoices, delivery documents, documentation relating to customs clearance process, etc. We do not provide your personal data to any third party except for the purposes relating to our direct contractual obligations. Upon completion of order processing and expiry of the warranty period for the Products provided by our Company, we do not store or process any of your personal data. Please note, that our Company’s Confidential policy does not imply any advertising or marketing activities with the use of your personal data (including your Company name, address, your E-mail, phone number and other information provided by you with a view to placing an Order and organization of the Delivery).