FFT Spectrum analyzer of vibro-acoustic signals ZET 034

  • Wide dynamic range
  • Recording and processing of data received from multiple channels
  • PTP synchronization
  • Support of various ICP (IEPE)-standard transducers, DeltaTron / ISOTRON transducers,  and CCD sensors with voltage output
  • Data recording controls available at the front panel of the device

POR (price on request)

Specifications

of FFT Spectrum analyzer of vibro-acoustic signals ZET 034

Technical specifications
Analog input (ADC)
Number of analog inputs by voltage and ICP 4
ADC digit number 24
Frequency ranges of the simultaneously analyzed signals DC…20, DC…200, DC…2 000, DC…20 000 Hz
Max. sampling frequency 400 kHz
Antialiasing signals filtration up to 40 kHz
LPF filters: Butterworth filters 120 dB/oct for sampling frequencies 50 Hz, 500 Hz, 5 kHz, 50 kHz
Filters with frequency correction (IEC 61672-1:2002) А, В, С, D for 1-class precision noise meters
Max. input voltage at unitary amplification ratio ±10 V
Programmable amplification ratios 1, 10, 100, 1000
Input impedance 100 kOhm
Analog output (DAC)
Number of analog outputs 1
Frequency range of the generated sinusoidal signal 0,03… 20 000 Hz
Output impedance 50 Ohm
Max. output current 20 mA
DAC digit number 24
Max. output voltage value ±10 V
Digital input/output
Digital input 8 bit
Digital output 8 bit
Logic type of digital input/output TTL
Metrological specifications
Analog input (ADC)
Dynamic range 110 dB
Band-pass channels non-identity 0,1 %
Cross-channel phase difference 1° per 10 kHz
Band-pass intrinsic noise level at the maximal amplification ratio applied to the input 1 µV
Analog output (DAC)
Admissible relative error limit of the frequency set-point for the range of 0…20 000 Hz ±0,1 %
Admissible relative error limit of the frequency set-point for the range of 0,03…10 Hz ±10 %
Error limit of the set-point for output DC and AC ±(0,2 % + 2 mV)
Harmonic coefficient of the generated sinusoidal signal 0,1 %
Operational specifications
Dimensions 280 × 200 × 35 mm
Weight 1 kg
Type of supported transducers ICP (IEPE), DeltaTron, ISOTRON
Possibility of synchronization with other FFT Spectrum analyzers yes
Non-volatile memory volume (flash drive)* up to 32 Gb
Sampling frequency of data recording to the flash drive by a channel* 50 kHz
Time of data recording to the flash drive by all the channels at the maximal sampling frequency* 10,8 hours
Baud rate via HighSpeed USB 2.0 480 Mbps
Baud rate via Ethernet 100 Mbps

* This additional option should be ordered separately

Designation

of FFT Spectrum analyzer of vibro-acoustic signals ZET 034

Multi-functional FFT Spectrum analyzers ZET 034 are used for measurement of spectral components parameters (which are present in vibrational, acoustic and hydroacoustic signals), as well as for generation of electrical signals with normalized metrological characteristics.

FFT Spectrum analyzer ZET 034 can be used both in standalone mode and within the structure of automation and process control systems intended for scientific research purposes. Operating principles of the instruments of ZET 03X  series is based on parallel (synchronous) analysis of signals’ spectra.

When used together with the software ZETLAB ANALIZ, the FFT Spectrum analyzers allow to:

  • analyze signals in real-time mode and conduct analysis of previously recorded signals;
  • conduct octave- and 1/3-octave analysis based on the implementation of parallel digital filters;
  • perform narrow-band spectral analysis;
  • measure ВС and AC voltage;
  • measure electrical signals frequency;
  • generate sine and DC voltage signals;
  • record signals (to save digitized signal values to the memory with further recording to the hard drive).

Information on measurement parameters is displayed at the external devices in user-friendly format.

Turn-key solutions

based of FFT Spectrum analyzers ZET 034

Basic configuration

of FFT Spectrum analyzer of vibro-acoustic signals ZET 034

FFT Spectrum analyzer of vibro-acoustic signals ZET 034 - basic delivery scope

Standard delivery scope includes the following components:

  • Multi-channel data acquisition system ZET 034;
  • Power supply module;
  • Ethernet cable;
  • Cable BNC-BNC 0,6 m;
  • Plug 50 Ohm;
  • ZETLAB ANALIZ software;
  • Set of operational documentation.

Order form - If you want to place an order or to make a request regarding technical specifications of particular product, fill out the form below:

Data protection notification

Please note that the personal data provided by you is used exclusively for the purposes of fulfilling our contractual obligations, including, but not limited to: issuing invoices, delivery documents, documentation relating to customs clearance process, etc. We do not provide your personal data to any third party except for the purposes relating to our direct contractual obligations. Upon completion of order processing and expiry of the warranty period for the Products provided by our Company, we do not store or process any of your personal data. Please note, that our Company’s Confidential policy does not imply any advertising or marketing activities with the use of your personal data (including your Company name, address, your E-mail, phone number and other information provided by you with a view to placing an Order and organization of the Delivery).